Where California is burning, right now. Every circle on the map is a hotspot picked up in the last 24 hours by NASA satellites: size grows with the intensity of the fire, colour summarises how serious it is. Below the map you will find each hotspot with its nearest town and state, and how far it sits from the centre of the state.

Over the past twelve months satellites recorded 1,185 hotspots of significant intensity in California, 21.0% of everything detected across the states we cover.

The busiest month is September, with 248 hotspots — the heart of the fire season, when heat, dry fuel and wind line up.

The single most intense reading of the year came on September 7, 2025 near Shaver Lake, at roughly 30,540 megawatts of radiative power. Not every detection makes it onto the map: we plot a fire only when the heat measured around it adds up to at least 50 MW, or 40 MW when ten or more detections cluster together. Below that it is almost always a small field burn.

Wildfires in California

Continuously updated last satellite pass: 01:52 (Pacific Time)

3 fires detected

AlabamaAlaskaArizonaArkansasCaliforniaColoradoConnecticutDelawareFloridaGeorgiaHawaiiIdahoIllinoisIndianaIowaKansasKentuckyLouisianaMaineMarylandMassachusettsMichiganMinnesotaMississippiMissouriMontanaNebraskaNevadaNew HampshireNew JerseyNew MexicoNew YorkNorth CarolinaNorth DakotaOhioOklahomaOregonPennsylvaniaPuerto RicoRhode IslandSouth CarolinaSouth DakotaTennesseeTexasUtahVermontVirginiaWashingtonWest VirginiaWisconsinWyoming Springville (CA) — high intensity Portola (CA) — moderate intensity Sandy Valley (NV) — very high intensity

So far in 2026, 289,506 hectares have burned in California, across 630 fires mapped by satellite. These are Sentinel-2 burn perimeters: they count large fires, not every blaze.

  1. Springville (CA) California · 108.1 km away high intensity
  2. Portola (CA) California · 335 km away moderate intensity
  3. Sandy Valley (NV) Nevada · 386.7 km away very high intensity

38 minor detections not shown (likely agricultural burns)

This map shows thermal anomalies measured by satellite, not an official list of active fires: there is no public real-time feed of fire service dispatches. Satellites pass 6-8 times a day and clouds can hide a fire; conversely, a controlled burn may be detected.

Data: NASA FIRMS (VIIRS/MODIS) for hotspots; EFFIS/Copernicus for burned areas, CC BY 4.0. Boundaries: US Census (public domain). Place names: GeoNames, CC BY 4.0.

Official wildfire incidents in California

Since January 1, 2026, fire agencies have recorded 364 wildfires in California, burning 377,103 acres (152,608 hectares).

No wildfire in California is listed as active by NIFC right now.

Largest wildfires of 2026

FireCountyAcresStatusDiscovered
Bug Lassen County 93,733 Out Aug 8
Biscar Lassen County 69,352 Contained Jul 18
Plaskett Monterey County 29,993 Contained Aug 26
Timber Monterey County 25,350 Contained Aug 8
Santa Rosa Island Santa Barbara County 18,379 Contained May 15

Source: NIFC WFIGS Interagency Fire Perimeters (public domain), data as of Nov 21, 2026. These are fires reported as incidents by fire agencies, by state of origin. The satellite figure under the map (Copernicus EFFIS) also counts burns that were never reported as incidents, so the two totals differ.

How to read this map

The data is re-read every fifteen minutes, but the real cadence comes from the satellites: they pass overhead six to eight times a day. The time of the last satellite pass is always shown next to the title — that is the moment this map actually refers to.

This is not an official incident log. There is no public real-time feed of fire department or wildland crew dispatches, so what you see here are satellite detections, filtered to remove permanent heat sources — refineries, steel mills and gas flares that burn all year and are not wildfires. In an emergency, call 911.

Wildfire map — frequently asked questions

How are these fires detected?

Each hotspot is a thermal anomaly measured by NASA satellites: the VIIRS sensors (375-metre resolution) aboard Suomi-NPP, NOAA-20 and NOAA-21, plus MODIS (1 kilometre). Every satellite pass measures the fire radiative power in megawatts, which is what sets the size of the circle on the map.

How often does the map update?

The data is re-read every 15 minutes, but the real cadence comes from the satellites: they pass overhead 6-8 times a day, and the data is available within about an hour of each pass. That is why the time of the last satellite pass is always shown next to the title — several hours can go by between one pass and the next.

Why is a fire I have heard about missing from the map?

Three reasons are possible. The satellite has not passed over that area yet. Clouds or heavy smoke hid the fire at the moment of the pass. Or the fire is too small or too weak to clear the threshold we filter at: below that level the satellite mostly sees agricultural burns and brush.

Does the map show every hotspot the satellite sees?

No, deliberately. We exclude permanent heat sources — refineries, steel mills, gas flares — that burn all year and are not wildfires; in Texas in particular the Permian Basin flares would otherwise fill the map. We also exclude the faintest detections, which are almost always agricultural burns. The number of excluded detections is always shown below the map.

Does this data come from the fire service?

No. There is no public real-time feed of fire department or wildland crew dispatches: what this map shows are satellite detections, not an official record of active incidents. In an emergency, call 911.

What do the colours and circle sizes mean?

Size grows with the total radiative power of the hotspot, on a logarithmic scale: a circle twice as wide is not twice the fire, but an order of magnitude larger. Colour summarises the same measure in three levels: yellow for moderate intensity, orange for high, red for very high.